Always check release notes and upgrade procedures
provided with the firmware package and make sure you have a backup of current running-config before proceeding.
console#show ip interface out-of-band
IP
Address..................................... 172.28.1.3
Subnet
Mask.................................... 255.255.255.0
Default
Gateway................................ 172.28.1.1
Configured
IPv4 Protocol....................... DHCP
Burned
In MAC Address.......................... A4BA.DB75.604E
console#configure
console(config)#enable password MyPassw0rd123
console(config)#exit
console#copy running-config startup-config
This
operation may take a few minutes.
Management
interfaces will not be available during this time.
Are you sure you want to save? (y/n) y
Configuration
Saved!
console#copy tftp://10.24.2.2/PCM6348v5.0.0.4a22/PC7000_M6348v5.0.0.4.stk
image
Transfer
Mode.................................. TFTP
Server
IP Address.............................. 10.24.2.2
Source
File Path............................... PCM6348v5.0.0.4a22/
Source
Filename................................ PC7000_M6348v5.0.0.4.stk
Data
Type...................................... Code
Destination
Filename........................... image
Management
access will be blocked for the duration of the transfer
Are you sure you want to start? (y/n) y
TFTP
code transfer starting
13401460
bytes transferred...
File
contents are valid. Copying file to flash...
Distributing
the code to the members of the stack!
File
transfer operation completed successfully.
console#show version
Image
Descriptions
image1 : default image
image2 :
Images currently available on Flash
unit image1 image2 current-active next-active
-----
------------ ------------ ----------------- -----------------
1 4.2.1.3 5.0.0.4
image1 image1
2 5.0.0.4 4.2.2.3 image2 image2
console#boot system 1 image2
Activating
image image2 ..
console#boot system 2 image1
Activating
image image1 ..
console#show version
Image
Descriptions
image1 : default image
image2 :
Images currently available on Flash
unit image1
image2 current-active next-active
-----
------------ ------------ ----------------- -----------------
1 4.2.1.3 5.0.0.4
image1 image2
2 5.0.0.4 4.2.2.3 image2 image1
console#update bootcode
Update bootcode and reset (Y/N)?
Issuing
boot code update command...
Validating
boot code from image...CRC Valid.
FROM CMC:
$ getioinfo
Switch-1 Dell PowerConnect M6220 Gigabit Ethernet Present
OK ON Master
Switch-2 Dell PowerConnect M6220 Gigabit Ethernet Present
OK ON Master
Switch-3 Dell PowerConnect M6348 Gigabit Ethernet Present
OK ON Member
Switch-4 Dell PowerConnect M6348 Gigabit Ethernet Present
OK ON Master
Switch-5 M8428-k 10GbEE-FCoE/8Gb FC SW 10 GbE KR Present OK ON Master
Switch-6 N/A None Not Present N/A
N/A N/A
$ connect switch-4
connect:
acquiring remote port.
Connected
to remote port.
Escape
character is '^\'.
console>en
Password:********
console#show version
Image
Descriptions
image1 : default image
image2 :
Images currently available on Flash
unit image1
image2 current-active next-active
-----
------------ ------------ ----------------- -----------------
1 4.2.1.3 5.0.0.4
image2 image2
2 5.0.0.4 4.2.2.3 image1 image1
console#show switch
Management Standby Preconfig
Plugged-in Switch Code
SW Status
Status Model ID Model ID Status Version
---
---------- --------- ------------- ------------- ------------- -----------
1 Mgmt Sw PCM6348 PCM6348 OK 5.0.0.4
2 Stack Mbr
Oper Stby PCM6348
PCM6348 OK 5.0.0.4
Reference: support.dell.com
Reference: support.dell.com
